The Short Version
Plan the curtain pole first, because ready-made curtains are sized to the pole, not the window. Measure the pole without its finials. Then measure the drop from the top of the pole for eyelet curtains, or from the bottom of the rings for pencil pleat. Choose a pair that measures 1.5 to 2 times the pole length when the two curtains are added together, and the nearest drop that won’t fall short. The curtain size calculator does the matching for you.
Most curtain mistakes happen before anything is ordered. A pair that barely covers the glass. A hem that stops a few centimetres above the sill. Curtains that block half the window even when they’re open. Each of these comes down to measuring the wrong thing.
Measuring for ready-made curtains takes about five minutes per window once you know where to put the tape. Here’s how to do it, step by step.
What you need
A metal tape measure, a pencil and paper, and a step ladder to reach the top of the window. Avoid fabric tapes. They stretch with use and give a smaller figure than the real one. Write each measurement down as you go and note which room it belongs to.
Step 1: Start with the pole, not the window
Ready-made curtains are sized to the pole or track they hang from, so the pole decides everything else. If a pole is already fitted, skip to step 2.
If not, plan where it will go. A pole usually sits 10 to 15cm above the top of the window frame. It should also extend 15 to 20cm past the frame on each side. That extra length gives the curtains somewhere to sit when they’re open, so they don’t cover the glass and cut out light. It makes the window look wider too.
The curtain pole calculator works out the length you need, which extendable pole covers it and whether you need rings. Curtain poles at Homefords come in three extendable lengths: 120 to 210cm, 160 to 300cm and 180 to 340cm.
Step 2: Measure the width
Measure the pole from end to end, leaving out the finials. These are the decorative ends, and curtains can’t hang on them. On a track, measure the full length of the track.
If the pole isn’t up yet, measure the window frame from outside edge to outside edge and add the overlap from step 1. A 120cm window with 15cm on each side needs a pole of around 150cm.
Take the measurement in two places. Windows in older houses are rarely perfectly square, and the larger figure is the safer one to use.
Step 3: Measure the drop
The drop is the length of the curtain from the top to the hem. Where you start measuring depends on the curtain heading.
Eyelet curtains
Measure from the top of the pole. The pole runs through the eyelets, so the top of the curtain sits at roughly the same height as the top of the pole. If you’re still choosing a pole for eyelets, this guide to the best curtain pole for eyelet curtains covers diameter and fit.
Pencil pleat curtains
Measure from the bottom of the curtain rings, or from the top of the track. That’s the point the hooks hang from.
Where should the curtains finish?
Decide this before you measure down, because it changes the number you write down.
- Sill length: stop about 1cm above the sill. This is the best choice when there’s a radiator, a desk or a window seat below the window.
- Below sill: finish around 15cm below the sill. This covers the gaps around the frame and suits most bedrooms.
- Floor length: stop about 1cm above the floor so the hem doesn’t drag or collect dust.
Measure the width along the pole and the drop from the top of the pole down to where the curtains will finish.
Step 4: Match your measurements to a ready-made size
Ready-made curtain sizes in the UK give the width first and the drop second, usually in inches. The width is for each curtain, not the pair. So a pair of 66 x 72 curtains is two curtains, each 66 inches wide and 72 inches long.
For a gathered look that closes properly, the two curtains added together should measure 1.5 to 2 times the pole length. Any less and they hang flat across the window, or don’t meet in the middle.
| Curtain width | Each curtain | Pair together | Suits a pole of about |
|---|---|---|---|
| 46″ | 116cm | 232cm | Up to 155cm |
| 66″ | 168cm | 336cm | 155 to 225cm |
| 90″ | 228cm | 456cm | 225 to 300cm |
Poles longer than 300cm usually need two pairs. The calculator tells you when that’s the case.
For the drop, pick the standard size that’s closest to your measurement without falling short:
| Drop | In cm | Usually suits |
|---|---|---|
| 54″ | 137cm | Sill length on most standard windows |
| 72″ | 183cm | Below sill, or floor length on short windows |
| 90″ | 228cm | Floor length in most rooms with a standard ceiling height |
A curtain that’s slightly too long can be taken up. One that’s too short can’t be fixed. Pencil pleat tape usually has more than one row for the hooks, which lets you raise the curtain a little without sewing. Ready-made sizes can also vary by up to 5% either way, so round up if your measurement is right on the limit. The curtain size guide lists every standard size in both inches and centimetres, and 90 x 90 curtains are the most popular choice for floor length.
Let the calculator do the maths
Enter your pole or window width and the drop. The curtain size calculator gives you the ready-made size to buy, how many pairs you need and the pole length to go with them.
Work out my curtain sizeCommon measuring mistakes
- Measuring the glass instead of the pole. Curtains sized to the glass end up too narrow to close and too small to frame the window.
- Reading the width as the pair. A 66 inch width means each curtain is 66 inches wide. The pair together is double that.
- Measuring eyelet curtains from below the pole. Start at the top of the pole, or the curtains will finish higher than planned.
- Forgetting the radiator. Floor-length curtains over a radiator trap heat behind them. Sill length works better here.
- Measuring once. Check the width and the drop in two places and use the larger figure.
Measuring a whole property
Landlords, holiday let owners and hotels often need to measure every window in a building at once. Label each window by room and floor as you go, because two windows that look the same are often a few centimetres apart. The calculator keeps a running list as you add each window and totals the order by size. Copy the list when you’re done and use it to place a single order.
There’s no minimum order, delivery is free on orders over £100 and 5% comes off orders over £500 automatically. If you’re furnishing several rooms, it’s worth looking at how to buy curtains in bulk. All the size calculators work the same way, so you can measure for blinds, bedding and tablecloths in the same visit.
Curtain measuring questions
Do you measure the window or the pole for curtains?
The pole. Curtains are sized to the pole or track they hang from. Only measure the window when the pole isn’t fitted yet, and then add 15 to 20cm on each side.
Is the curtain width for one curtain or the pair?
For one curtain. Ready-made sizes always give the width of a single curtain, even when they’re sold as a pair.
What do W and D mean in curtain sizes?
W is the width and D is the drop. A pair labelled W66 x D72 has two curtains, each 66 inches wide and 72 inches long.
Should curtains touch the floor?
Not quite. Floor-length curtains look best finishing about 1cm above the floor. That keeps the hem clean and lets the curtains move freely.
Ready to choose? Browse the full range of ready-made curtains, from eyelet and pencil pleat to blackout and thermal.













